T-FAL Prima

Prima All your bases are covered with the Prima.

Easy to handle, even easier to adore. The ultimate in steam iron design.

Reference : FV3758Q0

The term “user-friendly” was invented for the Prima.


Prima is an intuitive iron that’s sure to become every garment’s best friend. It features powerful 60g/mm bursts of steam, 1400 watts of power, plus a neat anti-slip heel and a comfort handle for precision and control.

Plus, the three-way automated shut-off provides peace of mind after those hurried, last minute steam sessions. Effortlessness has never looked so chic. 


 Stainless steel soleplate for good scratch resistance

 The stainless steel material is ultra resistant for more durability.

 Steam boost to remove even the toughest creases

 In case of particularly tough creases, the shot of steam flow reaches up to 60g/min for smooth ironing.

  Continuous steam ouput to ease crease removal

  Continuous steam output of up to 25g/min gives you the ideal constant amount of steam to efficiently remove all creases.

 Anti-drip to keep the linen spotless

 When ironing delicate fabrics at low temperature, the anti drip prevents water from dripping on your linen.

 Smart safety auto-off

 When accidently left unattended, the iron automatically turns off. If left on it's heel, it will switch off in 8 minutes. If left on the soleplate or on the side, it only takes 30 seconds before the iron shuts off.

 XL cord for unrestrained movement

 For convenience and easy handling an extra long cord equips your iron.

* Anti-drip technology protects your garments: no stray drops before Prima reaches ideal steam temperature.

 The smooth handle ensures a pleasent grip of the appliance for comfortable ironing.

3-way auto shut-off (intelligent design perk with your safety in mind), temperature indicator light (so you know exactly when you’re set to go)

Anti-drip prevents dripping before iron reaches the proper steam temperature

   Thanks to a 300mL watertank capacity, you will have long ironing sessions.

Vertical steam capabilities allows you to steam hanging garment

 Convenient function to quickly refresh or remove creases  on hanging garments, jackets, delicate fabrics, etc.

Spray nozzle so you can easily moisten fabric as your iron

   The spray moisterizes the fabrics to help you remove the difficult creases.

Expert anti-scale cleaning system for a constant steam flow and optimized performance.

 Your Tefal iron combines a preventive and a cleaning  device against calc.
Action 1:The integrated anti-calc  device reduces the formation of calc.
Action 2: The  Anticalc system makes the cleaning operation of your iron extremely  easy. A regular maintenance will ensure durable steam performance.

Water tank capacity 300  ml
Water filling hole Medium  

Frequent questions
Choose a board that is height-adjustable to adjust it to your body. It should be steady and robust so that you can place the ironing appliance on it.
The board should be perforated to allow the steam to pass through the fibres of the fabric to soften it and make ironing easier. The ironing board cover should also be suitable to allow the flow of steam through.
• Tap water:
Your appliance has been designed to work with tap water. If the water in your area is very hard, mix 50% tap water and 50% distilled water.
In some regions near the sea, the salt content in your water may be high. In this case, use distilled water only.
• Softener:
There are several types of softeners and the water of most of them can be used in your appliance. However, some softeners, and particularly those that use chemical products such as salt, may cause white or brown stains, this is particularly the case with filter jugs. If you encounter this type of problem, we recommend trying to use untreated tap water or bottled water. Once the water has been changed, several uses will be necessary to solve the problem. We recommend trying the steam function for the first time on an old item that can be thrown away in order to avoid damaging your clothes.
Do not use rain water or water containing additives (such as starch or perfume) or water from clothes dryers, water from refrigerators, air conditioners etc.
There could be several reasons for this:
• You are not using the right type of water (Refer to the FAQ "What water should I use for ironing ?").
• You have used a starch type product on your laundry (Always spray to the reverse side of the fabric to be ironed and clean your iron afterwards.).
• Fibres from clothes have been trapped in the holes in the iron and have become carbonised.
• The clothes have not been rinsed enough and there is detergent left on them or you have ironed a new item of clothing before washing it.
• See the instructions for use to find out what type of water is appropriate and clean the soleplate from time to time with a damp sponge.
It is essential to select the right ironing temperature.
Your iron has a built-in thermostat controlling the temperature very precisely over the entire surface of the soleplate. The thermostat dial contains international markers with dots corresponding to three ironing temperatures.
Make sure that you use the right temperature for your clothes:
• Marker with 1 dot for synthetic fabrics.
• Marker with 2 dots for wool and silk.
• Marker with 3 dots for cotton and linen.
• Don't use the Boost steam button intensively. Wait few seconds between each use.
• The temperature button must be placed on Steam area (between 2 dots and MAX).
• Use steam only when the iron is hot (the light must be off).
This function allows you to iron fabrics in situ or on a hanger.
To do this, set the iron temperature button to the maximum position.
• Leave the item on a hanger and gently pull the fabric with one hand.
• Press the steam control button intermittently and move the iron from top to bottom.
As the steam produced is very hot, it softens the fibres and removes creases.
Note: Never use the vertical steam function on an item being worn by anyone.
Yes and you do not need to fill the tank with water. Set the variable steam control to Dry and set the temperature to suit the type of material (care points •, ••, •••).
At the end of your ironing session, we would suggest that once your iron has cooled down, you should wipe over the soleplate and around the steam holes to remove any burned fibres that may have started collecting around the steam holes.
If it has not been used for a long time (for example several weeks), use it over the sink for a few minutes to remove any residue that could stain your laundry.

No, leave the iron to cool down before putting it away and follow the 4 tips: empty out the water remaining in the tank, set the thermostat to the minimum, close the steam control and stand it upright or place it on the base (depending model).
No, you must always unplug the iron before filling it.
To avoid damaging the soleplate, follow this advice:
• Always place your iron on its heel rest or its base (depending on model),
• Avoid ironing over abrasive items (buttons, zip fastenings, etc.),
• Never clean your iron’s soleplate with abrasive or metallic pads.
Shiny marks can appear on some fabrics, especially on dark coloured fabrics. We would advise ironing dark clothes inside out and using the correct temperature.
If ironing mixed-fibre fabrics, set the temperature for the most fragile fibre.
Important: The iron takes longer to cool down than to heat up. We recommend that you start with fabrics to be ironed at a low temperature.

If your iron has an anti-calc system, you should clean the anti-calc valve once a month. To do this, unplug the iron and leave it to cool for 30-45 minutes. Empty the water and remove the valve, holding it by the top. Let the anti-calc valve soak for 4 hours in a glass of commercially available white vinegar or natural lemon juice, then thoroughly rinse the anti-calc valve under tap water. Reposition the anti-calc valve into your iron. Warning! Never touch the end of the anti-calc valve. the iron does not work without the anti-calc valve.
Firstly, fill the iron tank to MAX with water.
Set the thermostat control to Max and the steam control on DRY and switch on.
Place the iron on its heel and leave to heat up for around 5 minutes.
Unplug the iron then hold your iron horizontally above the sink.
Remove the anti-scale valve (or set the control to self-clean/autoclean depending on the model). Steam, water and scale deposits will leave the steam chamber through the steam holes and the iron will be clean.
At the end of the operation, push the anti-calc valve back into position. When your iron is cold, you will also be able to use your vacuum to gently suction limescale and dirt that may have clogged the holes in the soleplate.
Four good tips:
After use, empty the tank, close the steam control, set the thermostat to minimum and stand the iron upright or place it on the base (depending on model).
Use a damp soft cloth to wipe your iron and never use cleaners or solvents.
If your iron has an auto-clean function, refer to the instruction manual before using it.
• Always use untreated water in your iron. If your water is very hard, we recommend you use a mix of 50% untreated tap water and 50% distilled water.
• Avoid placing your iron on sharp objects such as zip fasteners and metal buttons.
• Do not put your iron down flat on rough surfaces.
You must take precautions so that using your iron is risk-free.
Of capital importance… Never leave a hot iron unattended.
This is not only to avoid overheating of the iron or the surface on which it is placed but also to ensure that no-one gets burned. If safety is one of your main concerns, choose an iron that has an automatic cut-off function.
And never, never…
Never leave a hot iron within reach of children or pets who risk knocking it over and injuring themselves.
Like any electrical appliance, never put your iron in water.
Do not use an iron that has fallen down or has a damaged power cord. If you have the slightest doubt concerning the condition of your iron, contact the Service Centre.
Always unplug your iron before leaving it, cleaning it or filling it with water (unless it is a model that has a removable water tank). Regularly check the water level to ensure that there is always enough.
It is not designed for the water to be removed completely. It is okay to use or store the iron even with a small amount of water remaining. When storing, please remove as much water as possible and store in an upright position.
• The Durillium soleplate:
Regularly clean the soleplate with a damp, non metallic washing up pad. For easier, non-corrosive cleaning of your iron’s soleplate, use a damp sponge on the soleplate while it is still warm.
If cleaning dirt off is an issue, use the stick which is made specifically for cleaning the Durillium soleplates.
• The stainless soleplate:
Clean the soleplate of your iron when it is cool with a damp cloth or a non-abrasive sponge.
• The autoclean soleplate:
It is recommended that you use a soft damp cloth on the warm soleplate, in order not to damage the surface.
Warning: The use of iron cleaner will cause damage to your soleplate’s autoclean coating.
Never use any descaling agent or vinegar when rinsing the boiler: they could damage it.
• Self-cleaning: heat the iron, unplug it, remove the anti-calc valve and spray the iron over the sink.
• Cleaning the anti-calc valve: Remove the antiscale valve and soak the valve in a cup of white vinegar or plain lemon juice for 4 hours.
3 possible causes:
• No mains supply: Check that the mains plug is properly inserted or try plugging the iron into a different socket.
• Temperature control set too low: Set the temperature control to a higher temperature.
• The automatic electronic cut-out* is active: Move your iron
* depending on model
Always set your iron to the 'No Steam' function before you start to fill.
Gently shake your iron to reactivate it, the lights should start to flash and then the product should start to heat up.
Some irons (depending on model) can produce steam when set on the One dot setting, however, the majority of our irons will only produce steam when set on the 2 dot or 3 dot setting. When you look on your iron's thermostat dial you will notice that the 2 dot and 3 dot settings have a shaded background, this indicates that the iron will produce steam when the dial is set inside this shaded area.
Not all of the steam holes release steam, the smaller holes on the soleplate that look like they might be steam holes are actually designed to assist soleplate glide ability.
There is not enough water in the tank. Fill it up with the quantity indicated in the instructions for use and push spray button several times to fill the system complete.
Many irons contain a thermostat light and an auto-off light (Check your iron for these features.). It is normal for the thermostat to turn on and off. It indicates the thermostat is working and your soleplate is being maintained at the desired temperature. If the auto-off light blinks, you must disengage the auto-off function. This is done by gently shaking the iron which will allow the iron to reheat.
When heating your iron for the first time, you may notice a small amount of odour and smoke, this is simply the engineering residues from the manufacturing process burning off. These are harmless and will quickly disappear.
It is normal. Your iron generates a lot of steam; this steam is condensing on the board. Some waterdrops could appeared underneath the ironing board and fall on the flooring.
Your iron has been stored horizontally, without draining the water tank and with the selector placed on steam position. When you store your iron horizontally, check that the tanks is empty and the selector on "DRY" position.
Check the following points:
• The tank is empty or almost empty; add more water,
• The selected temperature is too low and does not allow steam to be produced; set the thermostat to the steam zone (between 2 dots and MAX),
• If your iron has a Dry/Steam control, set it to the Steam position,
• Scale has built up in your iron; descale it,
• Your iron has an intelligent system (a moving sensor) which temporarily stops steam being released when the iron is not moving, even when it is placed horizontally. This function eliminates wasted steam while you are handling the clothes!
Please check the following points:
• The tank is empty or almost empty; add more water.
• The selected temperature is too low to use this function; set the thermostat to the zone between 3 dots and MAX.
The "supersteam" or "turbo" function should not be used intensively – wait a few seconds between pressing the button.
You are filling the tank with the Dry/Steam control set to Steam – it needs to be in the Dry position. Or, you have over-filled your iron – do not go beyond the "MAX" level on the tank.
Some laundry starches and synthetic fibres may stick to the surface of the iron. Please clean the Iron's surface.
This is probably crystallized calcium chlorohypochlorite. Carry out the self-cleaning instructions in the instruction manual two or three times. If that hasn't resolved the problem, it may be that your iron needs repair. Please contact the service centre.
The internal parts may make metallic noises with the change in temperature. There is nothing wrong with it.
Do not use your appliance. To avoid any danger, have it replaced by an approved repair centre.
This may be due to the use of chemical descaling agents or additives in the water for ironing. Never use this type of product in the water tank (see our recommendations regarding water to be used). Some residues could also been present in the steam chamber or on the soleplate; use the self cleaning function (Depending model). All linen, especially new garments, must be washed and rinsed thoroughly to remove any soap and chemical deposits before you iron them. If these are not removed by washing they may appear later out of the soleplate in the form of small brown or white spots or streaks on your linen.
Use the right temperatures on the thermostat for the right fabrics. A reason for sticking may be the use of starch. If you want to use starch, simply spray it on the reverse side of the garment, so that there is no contact between the soleplate and the starch. Clean the soleplate from rubber prints of fabric (Which always must be ironed on reverse side of the rubber prints).
The anti-calc collector is a scale collector which automatically collects the scale which forms inside your iron. The amount of scale collected depends on the hardness of your water.

The electronic system cuts the power and the auto-stop light flashes if the iron is not moved for more than 8 minutes (on its heel rest or base) or is left flat for more than 30 seconds. To turn the iron back on, gently shake it until the light goes out.
Your appliance contains valuable materials which can be recovered or recycled. Leave it at a local civic waste collection point.